Press and hold the windows key and the b key at the same time while the computer is off. Except for the fact that there is no image on the monitor. Listen as you power on the computer and observe the lights if your computer turns on but there's no display on the monitor, turn your computer completely off and get down next to it before you hit the power button again. The fan on the card turns on when the computer is started, but nothing else works. • disconnect the power and data cables from all the drives inside the computer (hard drives, dvd/cd drives).
If possible, replace the video adapter. After another 2 seconds the computer turns itself back on again. New computer build pc turns on but no video output (read 4167 times) 0 members and 1 guest are viewing this topic. Press and hold the windows key and the b key at the same time while the computer is off. The computer is powering on, everything seems ok but nothing on the screen!!! Is there any settings that i am missing. After the power is completely off, turn on your pc and test to see if it will boot normally. Sometimes it's possible that when you turn on your computer but the display remains still and shows nothing, and the main reason behind your monitor's showing no signal or check video cable error on the screen is all because of some minor or maybe a major fault in your computer's hardware.
July 26, 2014, 09:48:54 am.
Power off your computer while in a power saving mode by holding the power button down for 3 to 5 seconds. Connect the video cable and turn on the computer. Reseat the card or replace it outright. If your monitor works on another computer, the video card is bad. Sometimes an improper shutdown can cause the video to be sent to a different display adapter or output. When i boot the computer up, the video card's fan is spinning and the computer seems to power on fine. Sometimes it's possible that when you turn on your computer but the display remains still and shows nothing, and the main reason behind your monitor's showing no signal or check video cable error on the screen is all because of some minor or maybe a major fault in your computer's hardware. Try removing video card from the affected computer and installing it in another computer. Troubleshoot the cause of the beep code if you're lucky enough to get one. Press and hold the 'mute' button on your remote for 5 seconds to ensure your screen isn't muted. After the power is completely off, turn on your pc and test to see if it will boot normally. While still pressing both keys, hold down the power button for one second, and then release the power button and the keys. Disconnect the main ac power by either shutting off the power button on the back of your power supply or simply pulling out the power cable.
Reconnect the power cord, and power on the television. My video card isn't working. We can work from there. This time it stays on but i have no monitor output. The fans actually go crazy, spinning at full force.
Once the power button is pressed, the system will power on and proceed to the post checks where you may see the diagnostic led's illuminate for a short time. The computer is powering on, everything seems ok but nothing on the screen!!! Turn on the monitor and wait about ten seconds while the computer starts. If the monitor is connected to your video card, try connecting it to the video output of the motherboard. Connect the video cable and turn on the computer. You might hear beeping sounds. O.k., now unplug the power cable from the power supply and press power button for 10 seconds. **click the kudos thumb up on the left to say 'thanks'**.
In order to fix the error that there is no signal coming from your computer, you can try to check whether the video cable is connected firmly first.
O.k., now unplug the power cable from the power supply and press power button for 10 seconds. The cable to connect the hard drive that ends up going to the other hard drive (the primary, that is an ssd) has 2 places where i could connect the secondary hard drive. New computer build pc turns on but no video output « on: The loose connection between computer and monitor is the key factor to give rise to dvi no signal problem. We can work from there. The computer is powering on, everything seems ok but nothing on the screen!!! How to fix your pc turns on but no display. After another 2 seconds the computer turns itself back on again. Check the video adapter and make sure it's seated properly. **click the kudos thumb up on the left to say 'thanks'**. I've got a dell dimension 8400 and a 2001fp monitor. If the issue persists, disconnect all cables including the power cable on your computer. Computer will not boot and there is no video.
When i boot the computer up, the video card's fan is spinning and the computer seems to power on fine. • remove all the cards installed in the pci slots including the video card. July 26, 2014, 09:48:54 am. Press and hold the 'mute' button on your remote for 5 seconds to ensure your screen isn't muted. If the monitor is connected to your video card, try connecting it to the video output of the motherboard.
Listen as you power on the computer and observe the lights if your computer turns on but there's no display on the monitor, turn your computer completely off and get down next to it before you hit the power button again. Could the 180 watt power supply be to weak to power the card. The cable to connect the hard drive that ends up going to the other hard drive (the primary, that is an ssd) has 2 places where i could connect the secondary hard drive. The fan on the card turns on when the computer is started, but nothing else works. If the operating system does not start for any reason, this is called a no boot. We can work from there. Connect the video cable and turn on the computer. While still pressing both keys, hold down the power button for one second, and then release the power button and the keys.
• remove all the ram sticks (same rules as above).
Press the power key and hold it for like 1 min and restart the computer. Try removing video card from the affected computer and installing it in another computer. Reconnect the power cord, and power on the television. O.k., now unplug the power cable from the power supply and press power button for 10 seconds. Once the power button is pressed, the system will power on and proceed to the post checks where you may see the diagnostic led's illuminate for a short time. After another 2 seconds the computer turns itself back on again. Now i'm gonna change the board and it's probably gonna fix the problem. In order to fix the error that there is no signal coming from your computer, you can try to check whether the video cable is connected firmly first. Disconnect the main ac power by either shutting off the power button on the back of your power supply or simply pulling out the power cable. We can work from there. The fans actually go crazy, spinning at full force. If the monitor is connected to your video card, try connecting it to the video output of the motherboard. Sometimes it's possible that when you turn on your computer but the display remains still and shows nothing, and the main reason behind your monitor's showing no signal or check video cable error on the screen is all because of some minor or maybe a major fault in your computer's hardware.
Computer Powers On But No Video - What To Do If Pc Doesn T Turn On But Its Fans Do - The computer is powering on, everything seems ok but nothing on the screen!!!. The cable to connect the hard drive that ends up going to the other hard drive (the primary, that is an ssd) has 2 places where i could connect the secondary hard drive. Troubleshoot the cause of the beep code if you're lucky enough to get one. I've got a dell dimension 8400 and a 2001fp monitor. Now i'm gonna change the board and it's probably gonna fix the problem. This time it stays on but i have no monitor output.